This is Modemsite.com
Modemsite.com - Helping you get the best performance from your modem
 Troubleshooting News Technical Search
 Home Forum 56 Premium Site Map
HomeTroubleshooting Modem Log  

Understanding Your Modem Log

Windows 95/98/NT/2k/Me/XP all include the ability to record a modem log. This log can help you pinpoint a variety of problems you might encounter while attempting to make a connection.

The information below applies to Windows 95/98. See this page for Windows 2000 & XP Modemlog.

Windows 95: The Option to record a log file is set from:
Start -> Settings ->
Control Panel->
Modems ->
Click your Modem listing,
Click Properties
Click the Connection tab
Click Advanced

On Advanced Connection Settings, set the checkbox Record a Log file. 

Click OK all the way out.

Note: This is also the area you enter any Extra settings, or initialization string for your modem.

Windows 98, 2K, ME & XP have similar options. - see Windows 2000/XP log setup.

Finding your Modemlog: 
Your next challenge is to locate the log. In Windows 95 & NT, the log is named Modemlog.txt. In Windows 98 and higher, it will be named <modemname>.log, where modemname is the name displayed in the modem list (above).
 Later versions of Windows will have a 'View Log' button on the modem properties screen to open the log.

Use Find Files to locate your log file. (Win98 name shown w/ wildcard)  

Once you've found your modem log file, open it with Notepad. (Notepad is good because it defaults to Courier fixed-space font.) The pane below shows parts of a modem log file. All entries have the date & time which is shown only on the first line to save space.
 

The modem log will identify the modem, the name of the .inf file beings used, as well as the section of the .inf file.
Port settings


The modem is sent AT &F (reset to factory defaults) and 2 lines of AT commands based upon the .inf file and options you've selected in CPanel->Modems.


Then, the modem is sent any 'extra settings' you may have entered in CPanel->Modems.


The modem is told to Dial...


And completes a successful connection at 48000bps.

When the modem disconnects, it is logged - and may contain information about the disconnect.

Modem Log Output

05-23-2000 08:30:33.292 - Lucent Win Modem in use.
- Modem type: Lucent Win Modem
- Modem inf path: oem0.inf
- Modem inf section: Modem_PNP_DSVD
- 57600,N,8,1
- Initializing modem.
- Send: AT<cr>
- Recv: AT<cr>
- Recv: <cr><lf>OK<cr><lf>
- Interpreted response: OK
- Send: AT &F E0 &C1 &D2 V1 S0=0\V1<cr>
- Recv: AT &F E0 &C1 &D2 V1 S0=0\V1<cr>
- Recv: <cr><lf>OK<cr><lf>
- Interpreted response: OK
- Send: ATS7=60S30=0L0M1\N3%C1&K3B0B15B2N1\J1X4<cr>
- Recv: <cr><lf>OK<cr><lf>
- Interpreted response: OK
- Send: ATE1-v90=17<cr>
- Recv: <cr><lf>OK<cr><lf>
- Interpreted response: OK
- Dialing.
- Send: ATDT;<cr>
- Recv: ATDT;<cr>
- Recv: <cr><lf>OK<cr><lf>
- Interpreted response: OK
- Dialing.
- Send: ATDT#######<cr>
- Recv: <cr><lf>CONNECT 48000 V42bis<cr><lf>
- Interpreted response: Connect
- Connection established at 48000bps.
- Error-control on.
- Data compression on.
.......
 
Remote modem hung up.
 

 Port settings - With a software-controller modem like the Lucent used in this example, a 'virtual' COM port is used - these port settings don't matter and the modem isn't limited to the port speed rate. Hardware modems that use a 'real' COM port are limited by this setting, and in most cases, 115.2k is the desired setting.

 Extra settings or init string - Note that your string follows the basic initialization of the modem, and in many cases is unnecessary. I do not recommend using a string if you don't know what it does, and if you do use a string, you should avoid &F, Z, W1 and other 'modem altering drugs'.

 The modem is told to Dial... And in a somewhat unusual and inefficient way, I might add. Notice how the modem is first given the ATD; command, and waits for the OK response before sending another D command with the actual number.

Disconnection - When the modem disconnects, log entries are made (the format and type of entries will vary among different versions of Windows). Some of the responses that may be seen include:

Hanging Up the Modem
Hardware hangup by lowering DTR
You (or something running on your computer) caused the disconnect
NO CARRIER The modem couldn't establish, or lost a connection and hung up
Remote modem hung up The modem at your ISP disconnected you
TSP(0000): Dropping Call
Hanging up the modem.
Hardware hangup by lowering DTR.
Detected CD dropped from lowering DTR

 
WindowsXP log entries when you (or something running on your computer) caused the disconnect.

Also see:
Modem Diagnostic Screens
Disconnections

 
Home  |  Links  |  Send Feedback  |  Privacy Policy  | Report Broken Link
Legal Page  |  Author's Web Sites   |  Log In   
 

Modemsite.com ©1998-2022 v.Richard Gamberg. All rights reserved.